Tag Archives: metal

Will This Stop the BP Oil Leak?

THIS IS MY SOLUTION FOR SEALING THE BP OIL LEAK If British Petroleum does decide to cut the up-riser off, this will expose the raw shaft into the well. It is vertical without any bends or debris and this will give them a straight shot down the well. This metal rod is telescoped in design so that it is smaller on the tip and gradually graduated into a larger diameter. The final diameter is fairly close tolerance to that of the well pipe. This end of the metal rod has a series of O-rings or seals that will help to seal the final stage. The top of the rod will basically have an oversize head on it so it will stop the rod from descending any further down the well than is desired. The rod I have shown is tapered or telescoped so it will allow the oil pressure to bypass the rod initially upon insertion. Once it has entered the pipe, the weight of the rod is more than adequate to overcome any of the oil pressures being exerted as it is approximately 20 to 25 feet long, and about 21 inches in diameter at the sealing end. The well pipe will guide the rod accordingly down the throat due to the telescoping shape of the rod. Once it bottoms out against the head and the top of the fresh cut pipe, the seal will be complete. The well will be plugged permanently but the rod still has the ability to be removed if needed. The rod can be made of stainless steel or whatever is best for this application. It can be solid or if desired it can be hollow for the purpose of still pumping oil. The ring on top would still need to be present for any continued modifications or repairs. A ball valve would need to be implemented into the design as shown in the diagram and a series of in-flow ports would need to be added along the lower extremities of the rod for the oil to enter and flow through the rod. It would be a good idea to have two ball valves, (not shown), one on top of the other in case of failure of one or the other. If the rod is hollow, then it needs to be longer so the loss in weight would be regained. The weight needs to be sufficient to force the rod into the well pipe and cause it to seat. This would seal the well as there would be no place for the oil to find a by-pass. I have other solutions that will work if the decision is to plug the up-riser and the pipe that has currently been the focus. JuliusBC Inventor/designer added by: JuliusBC

Is This a Solution to Stop the BP Oil Leak?

THIS IS MY SOLUTION FOR SEALING THE BP OIL LEAK If British Petroleum does decide to cut the up-riser off, this will expose the raw shaft into the well. It is vertical without any bends or debris and this will give them a straight shot down the well. This metal rod is telescoped in design so that it is smaller on the tip and gradually graduated into a larger diameter. The final diameter is fairly close tolerance to that of the well pipe. This end of the metal rod has a series of O-rings or seals that will help to seal the final stage. The top of the rod will basically have an oversize head on it so it will stop the rod from descending any further down the well than is desired. The rod I have shown is tapered or telescoped so it will allow the oil pressure to bypass the rod initially upon insertion. Once it has entered the pipe, the weight of the rod is more than adequate to overcome any of the oil pressures being exerted as it is approximately 20 to 25 feet long, and about 21 inches in diameter at the sealing end. The well pipe will guide the rod accordingly down the throat due to the telescoping shape of the rod. Once it bottoms out against the head and the top of the fresh cut pipe, the seal will be complete. The well will be plugged permanently but the rod still has the ability to be removed if needed. The rod can be made of stainless steel or whatever is best for this application. It can be solid or if desired it can be hollow for the purpose of still pumping oil. The ring on top would still need to be present for any continued modifications or repairs. A ball valve would need to be implemented into the design as shown in the diagram and a series of in-flow ports would need to be added along the lower extremities of the rod for the oil to enter and flow through the rod. It would be a good idea to have two ball valves, (not shown), one on top of the other in case of failure of one or the other. If the rod is hollow, then it needs to be longer so the loss in weight would be regained. The weight needs to be sufficient to force the rod into the well pipe and cause it to seat. This would seal the well as there would be no place for the oil to find a by-pass. I have other solutions that will work if the decision is to plug the up-riser and the pipe that has currently been the focus. JuliusBC Inventor/designer added by: JuliusBC

Paul Gray dead picture

Shown is the TownePlace Suites where Paul Gray, the bassist for Grammy-winning metal band Slipknot, was found dead, Monday, May 24, 2010, in Urbandale, Iowa. Paul Gray, bassist with the metal band Slipknot, was found dead Monday in a hotel room in Urbandale, Iowa. He was 38. Police said a hotel employee discovered Gray#39;s body in a room at the Town Plaza Hotel in Urbandale, a suburb of Des Moines. Foul play isn#39;t suspected. An autopsy is planned for Tuesday. A person who answered the pho

Read more:
Paul Gray dead picture

‘Iron Man 2’ Cast Reveals Inspiration For War Machine, Whiplash, Justin Hammer

Mickey Rourke went to prison for research, while Don Cheadle and Sam Rockwell … read comics? By Eric Ditzian, with reporting by Josh Horowitz Photo: MTV News Their characters have existed on the comic book page for decades, etched into readers’ minds long before the idea of adapting “Iron Man” for the big screen was even hatched. But that history of pen and ink, of well-established characterization, of colorful heroes and even more colorful villains, didn’t mean cast and crew were boxed in when it came to conceiving cinematic equivalents for characters like War Machine, Whiplash and Justin Hammer. In interviews conducted before “Iron Man 2” grossed $133.6 million during its opening weekend, the actors behind those Marvel creations — Mickey Rourke, Don Cheadle and Sam Rockwell — spoke with MTV New about the choices they made to make the characters their own. Rourke famously holed up in a Russian prison to capture the nuances of the villain Ivan Vanko, who ends up transforming himself into the laser-tendril-outfitted Whiplash. While his dialogue coach gave his Russian accent the OK, Rourke’s girlfriend, the Russian-born model Anastassija Makarenko, was less pleased. “She thought it sucked,” he laughed. Rourke’s preparation didn’t stop there. He insisted that Vanko have a mouthful of metallic dental work, a body covered in tattoos and a pet cockatoo. “[Director Jon Favreau] had to fight for the teeth and the tattoos and the bird. Everything was a little bit of a fight,” Rourke said. “The Marvel people, who could have easily said no, said yes. They trusted Jon, and Jon trusted me, and Robert was very supportive.” So what did Cheadle do to get into character as the metal-suited freedom fighter, War Machine? He headed straight to a Russian prison as well. “I discovered that once I’d been in there that it had nothing to do with War Machine,” he joked. “But I thought, ‘If Mickey Rourke’s going to do it, I got to do it.’ ” In actuality, probably all Cheadle needed to do was lift some weights, because the War Machine costume was seriously heavy and uncomfortable. “A great deal of it is CGI,” he explained. “The metal frame, the metal torso down to the waist was real and metal and inarticulate and cumbersome. I was thinking, ‘Why did I do this?’ Summer Stock looked so much better!” To portray the nefarious arms dealer Justin Hammer, Rockwell turned to the “Iron Man” comic books — up to a point. “I got the flamboyance of him in the comic book — the ascot and the smoking robe,” the actor said. And though they experimented with the idea of using that look in the movie, he said, “Eventually, we just did our own thing. Who knows? Maybe he’ll go there some day.” Check out everything we’ve got on “Iron Man 2.” For breaking news and previews of the latest comic book movies — updated around the clock — visit SplashPage.MTV.com . Related Videos MTV Rough Cut: ‘Iron Man 2’ Gear Up For ‘Iron Man 2’ With These New Clips Related Photos ‘Iron Man 2’ Premieres In Los Angeles ‘Iron Man 2’

The rest is here:
‘Iron Man 2’ Cast Reveals Inspiration For War Machine, Whiplash, Justin Hammer

But Did He Sign It?

Rocker Ozzy Osbourne has signed a lot of weird things over his career and after all these years one item still stands out. In an interview with the UK’s Q magazine , the metal legend revealed that a fan asked him to sign his colostomy bag. “This guy asked me to sign his colostomy bag. He put his hands down his pants and plopped this pink thing onto the table. I couldn’t even look at it.” Yeah, but did you sign it?

See the original post here:
But Did He Sign It?